Direct Energy Deposition: Difference between revisions
Jump to navigation
Jump to search
| Line 6: | Line 6: | ||
== Strengths & Weaknesses == | == Strengths & Weaknesses == | ||
=== Strengths === | |||
* '''Industrial scaling''': DED machines are often much larger then other print types, enabling the production of fairly large parts. | * '''Industrial scaling''': DED machines are often much larger then other print types, enabling the production of fairly large parts. | ||
* '''Part modification''': DED has the ability to add additional features onto weldable metal parts, allowing for the combination of different manufacturing technologies or repair of broken parts. | * '''Part modification''': DED has the ability to add additional features onto weldable metal parts, allowing for the combination of different manufacturing technologies or repair of broken parts. | ||
=== Weaknesses === | |||
*'''Surface finish''': Although the exact surface finish is dependent on the feed stocked, DED has very poor surface finish in general. | *'''Surface finish''': Although the exact surface finish is dependent on the feed stocked, DED has very poor surface finish in general. | ||
* '''High energy''': The constant melting of metal in the process uses very high amounts of energy. | * '''High energy''': The constant melting of metal in the process uses very high amounts of energy. | ||
| Line 33: | Line 35: | ||
|} | |} | ||
==Categories of DED== | ==Categories of DED== | ||
The two primary factors used to characterize DED printers is based on the type of feed stock and the type of energy source used to melt the parts | |||
''' | === Feed type === | ||
* '''Wire fed''': Wire feeding gives a consistent flow of material to the deposition pool. This means that little material is wasted, but since the amount of material being deposited limits the complexity of parts available. this limited geometry also means that the surface finish is greatly affected. | |||
* | * '''Powder fed''': Powder methods enable more complex geometries to be produced by changing the amount of powder deposited in a particular area. However, not all material being deposited ends up being used, and a recycling system must be used to prevent powder waste. | ||
* | === Energy sources === | ||
* | * '''Laser''': Laser based DED systems allow for precise control over the heat source. Lasers paired with powder are capable of producing the most complex geometries in this category of AM. | ||
* | * '''Plasma''': This tends to be the most energy efficient form of DED. Normally paired with wire feedstock, it is best suited for large scale manufacturing. | ||
* '''Electron beam''': This is one of the less common energy sources for DED systems. It is very fast, however, it must be done in a vacuum, increasing costs, but reducing potential contamination of the parts. | |||
== Technologies == | == Technologies == | ||
* WAAM: | * '''Wire Arc Additive Manufacturing (WAAM)''': The generic term for the combination of a plasma energy source and a wire feedstock. | ||
* PL: | * '''Powder Laser (PL)''': The generic term for a combination of a powder feed source with a laser energy source. | ||
* LENS: created by Optomec | * '''Laser Engineered Net Shaping (LENS'''): A proprietary technology created by Optomec that combines a laser power source and a powder feeding system. | ||
* EBAM: created by Sciaky | * '''Electron Beam Additive Manufacturing (EBAM'''): A proprietary technology created by Sciaky that combines an electron beam energy source, and a wire feedstock. | ||
* RPD: | * '''Rapid Plasma Deposition (RPD'''): A proprietary technology created by Norsk titanium that is an advanced version of WAAM. | ||
Revision as of 10:39, 5 October 2023
Process description
Direct Energy Deposition (DED) combines welding with other technologies to produce parts through additive manufacturing. In this process, a high power heat source is used to melt and deposit a feed stock directly onto a plate (typically welding it onto a sacrificial print bed). Each layer is welded onto the last until the part is fully formed. The part must then be cut from the build plate, and post processed, usually through subtractive manufacturing such as milling, to produce a finished product.
DED also has the unique ability to modify existing metal parts. By treating the old part as the print surface, it can build out new layers, similar to printing on a traditional build plate.
Strengths & Weaknesses
Strengths
- Industrial scaling: DED machines are often much larger then other print types, enabling the production of fairly large parts.
- Part modification: DED has the ability to add additional features onto weldable metal parts, allowing for the combination of different manufacturing technologies or repair of broken parts.
Weaknesses
- Surface finish: Although the exact surface finish is dependent on the feed stocked, DED has very poor surface finish in general.
- High energy: The constant melting of metal in the process uses very high amounts of energy.
- Post processing: DED prints often need to be machined to fix geometries and surface finishes.
Machine Property Ranges
| Low | High | |
|---|---|---|
| volume X/Y/Z (mm) | 200/200/200 | 5080/2794/2794 |
| resolution (mm) | 1 | .67 |
| layer height (um) | 800 |
Categories of DED
The two primary factors used to characterize DED printers is based on the type of feed stock and the type of energy source used to melt the parts
Feed type
- Wire fed: Wire feeding gives a consistent flow of material to the deposition pool. This means that little material is wasted, but since the amount of material being deposited limits the complexity of parts available. this limited geometry also means that the surface finish is greatly affected.
- Powder fed: Powder methods enable more complex geometries to be produced by changing the amount of powder deposited in a particular area. However, not all material being deposited ends up being used, and a recycling system must be used to prevent powder waste.
Energy sources
- Laser: Laser based DED systems allow for precise control over the heat source. Lasers paired with powder are capable of producing the most complex geometries in this category of AM.
- Plasma: This tends to be the most energy efficient form of DED. Normally paired with wire feedstock, it is best suited for large scale manufacturing.
- Electron beam: This is one of the less common energy sources for DED systems. It is very fast, however, it must be done in a vacuum, increasing costs, but reducing potential contamination of the parts.
Technologies
- Wire Arc Additive Manufacturing (WAAM): The generic term for the combination of a plasma energy source and a wire feedstock.
- Powder Laser (PL): The generic term for a combination of a powder feed source with a laser energy source.
- Laser Engineered Net Shaping (LENS): A proprietary technology created by Optomec that combines a laser power source and a powder feeding system.
- Electron Beam Additive Manufacturing (EBAM): A proprietary technology created by Sciaky that combines an electron beam energy source, and a wire feedstock.
- Rapid Plasma Deposition (RPD): A proprietary technology created by Norsk titanium that is an advanced version of WAAM.